Command and Processes Table - R

These tables list all commands and processes available in all Datamine Studio products. If your product has access to a command or process, the link on the left of the table displays a help file. If no link appears, the function isn't available in your product.

Symbols used in this table:

A green tick indicates that the module is part of the core system licensing for the specified product - no additional module is required.

X A red cross indicates the module is not part of the listed system and any commands held within it cannot be run (a separate product will be required).

� A blue diamond indicates the module is an optional extra for the specified system.

Note: For an explanation of the terms 'command', 'process' and 'macro command', see Command Table Introduction.

For Macro commands, see here.

Commands - R

Process Name										Description	More Help
ramp-between-2-points	X	X	X	X	X		X	X	X	Make ramp connecting two points, according to supplied criteria.
ramp-by-three-points	X	X	X	X	X		X	X	X	Make ramp connecting three points, according to supplied criteria.
ramp-curve-fit	X	X	X	X	X		X	X	X	Modify string so that its end tangentially fits another string.
rapid-digitize-switch										Modify string so that its end tangentially fits another string.	Command Help
rectangle-from-center-to-corner										Draws a rectangle with a center point and a corner point selected interactively.	Command Help
rectangle-from-corner-to-corner										Draws a rectangle with a center point and a corner point selected interactively.	Command Help
redo-last-undo										Redo the previous undo command	Command Help
redraw-display										Redraws currently displayed object overlays.	Command Help
redraw-strings-in-order										Redraw string data according to a nominated numeric data column from which a sequence of drawing can be determined.	Command Help
reduce-points										Reduces the number of points in a string by the percentage set using the reduction-percentage command.	Command Help
reduction-percentage										Used in conjunction with the reduce-points command. Specifies the percentage reduction.	Command Help
remove-string-crossovers										Removes string crossovers in the current view plane.	Command Help
rename-drillhole										Interactively rename drill holes.	Command Help
reposition-sirotiff										Reposition a SiroTIFFimage in the XYZ axes	Command Help
reset-georeferencing	X	X	X	X	X	X	X	X		Reset the current map georeferencing, returning the map to local coordinates.	Command Help
resolve-string-points										Resolves points from one string onto those of another string within a defined tolerance.	Command Help
results-annotation	X	X			X	X	X	X	X	Annotate perimeters with corresponding field value in results file.
reverse-string										Reverses the order of points for selected strings.	Command Help
reverse-view										Reverse the current view direction.	Command Help
rings-edit-hole-params-switch	X	X	X	X	X		X	X	X	Toggle the display of the Drillhole Parameters dialog on drillhole creation.
rings-move-drill	X	X	X	X	X		X	X	X	Reposition the drill relative to the rig center.
rings-move-rig	X	X	X	X	X		X	X	X	Move the drill rig within the drill drift outline.
rings-position-rig	X	X	X	X	X		X	X	X	Determine if a drill rig can be brought into position in plan view.
rings-rig-reversed-switch	X	X	X	X	X		X	X	X	Toggles rig direction.
rings-save-design-planes	X	X	X	X	X		X	X	X	Create a Section Definition file from strings intersecting the view plane.
rings-toe-snap-to-design-switch	X	X	X	X	X		X	X	X	Toggles the use of snapping when positioning hole toe positions.
rings-toe-spacing-marker-switch	X	X	X	X	X		X	X	X	Creates an intersecting road layout from two intersecting strings.
road-berm-offset-percentage	X	X			X	X			X	Berm tapering will gradually reduce the width of the berm where the berm meets the road in an open pit design.
road-berm-taper-switch	X	X			X	X			X	Toggles the use of tapering in road berm creation.
road-design-string-pair	X	X			X	X			X	Generate a road design string between two existing contours.
road-design-string-single	X	X			X	X			X	Generate a road design string from an existing perimeter.
road-outline-intersection	X	X	X	X	X		X	X	X	Creates an intersecting road layout from two intersecting strings.
road-tester	X	X			X	X	X		X	Interactively experiment with different road layouts over a pit wireframe, using the Ramp Layout tool.
road-string-colour	X	X			X	X			X	Set colour for road strings in open pit design.
roof-string-colour	X	X	X	X	X			X		Set color for roof strings in underground mine design.
rotate-string										Rotates a string interactively about a fixed anchor point.	Command Help
rotate-string-by-angle										Rotates the selected string(s) in the current view plane, about a selected point, by a specified angle.	Command Help
rotate-string-to-azimuth										Rotates a string about a selected point in the current view plane to a specified azimuth.	Command Help
rotate-wireframe									X	Interactive command for rotating a wireframe object using defined rotation angle and rotation point settings.

Processes - R

Process Name										Description	More Help
RANDOM										Generates random numbers	Process Help
RANK										Ranks values of a given numeric or alphanumeric field in a file.	Process Help
REBLOCK									X	This command re-blocks a block model by user specification of new X, Y and Z parent cell sizes. The origin of the model remains unchanged.
RECBLKST	X	X			X	X			X	Compare the volumes defined by outlines between an initial and final topography.
RECCOP										Copy a group of records from one file to another.	Process Help
RECMODEL									X	Compare the volumes defined by two model key fields.
RECMODWF									X	Compare the volumes defined by wireframe solids with the contents of cells classified by keyfields in the model file.
REGMOD									X	Produces a regular cell model from any type of Datamine ore body block model.
REGMOW										Produces a regular cell model for pit optimization.	Process Help
RENAME										Renames a Datamine file in the project.	Process Help
REPORK										General tabulating report generator with provision for separate keyfield sections.	Process Help
REPORT										Generates a tabulation to your own format requirements.	Process Help
RESCAT										Reserve Category Modeling.	Process Help
RESTRI										Performs a relational restriction operation.	Process Help
RNLM			X	X		X	X	X	X	R - mode non linear mapping groups together elements using the angular distances calculated from the Pearsson correlation coefficient matrix.
ROTORDER									X	Converts rotation axes and angles to a specified rotation order.